Support

If you have a problem or need to report a bug please email : support@dsprobotics.com

There are 3 sections to this support area:

DOWNLOADS: access to product manuals, support files and drivers

HELP & INFORMATION: tutorials and example files for learning or finding pre-made modules for your projects

USER FORUMS: meet with other users and exchange ideas, you can also get help and assistance here

NEW REGISTRATIONS - please contact us if you wish to register on the forum

Triggering switches with Midi notes.

For general discussion related FlowStone

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Sun Sep 30, 2018 5:57 pm

OH, really, thats it , and this works as polyphonic?
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Sun Sep 30, 2018 6:52 pm

Yep, this works, except it went back to a mono signal, checking if i did something wrong.
I changed the one you made to work with 12 stereo channels or 24 mono ,so each note was triggering a stereo channel.
With the ADSR that is lost and I am back to mono.

I can upload my schematic if you can open an alpha ?

Donated ;)
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Sun Sep 30, 2018 7:02 pm

With this configuration through the adsr I get mono.
Ones below are from before with no ADSR and they work as stereo.
Must say , I am a bit frustrated that my skill level is so low that I cannot figure this out .
I could obviously just have 2 Adsr´s with one set of controls but that seems like a workaround ;)



Mono.jpg
Mono.jpg (155.96 KiB) Viewed 12322 times
Last edited by lalalandsynth on Sun Sep 30, 2018 8:45 pm, edited 3 times in total.
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Sun Sep 30, 2018 7:10 pm

Stereo configuration

config.jpg
config.jpg (191.23 KiB) Viewed 12322 times
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby martinvicanek » Sun Sep 30, 2018 9:36 pm

You can go stereo like this:
StereoRoting.png
StereoRoting.png (16.82 KiB) Viewed 12319 times

Simply pack and unpack the L/R channels into a Mono4 stream - everything else remains unchanged.

There is a lot to optimize but that's for later. Thanks for the donation! :D
User avatar
martinvicanek
 
Posts: 1315
Joined: Sat Jun 22, 2013 8:28 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Sun Sep 30, 2018 9:40 pm

Thanks again , so simple ...unless you dont know how :)

:mrgreen:
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Sun Sep 30, 2018 11:36 pm

Hmm, everything sound distorted now.
Having a look, sounds fine in FS (EDIT: IT IS DISTORTED IN FS AS WELL: ,distorted in Reaper, previous version without ADSR sounded fine in Reaper

Not sure what happened , it sounded fine in mono.
No reason for it to be the Pack/unpack , already using that in the volume knob and Clip.

Its weird I can pull the gain from my test osc to -70 , still has no effect on lowering the sound.
Same thing in reaper , lowering the input file had almost no effect , almost like everything is normalized/maximized and distorted ?

Ok, so bypassing the adsr and going straight from pack to unpack solves the distortion , distortion happens at the adsr ,
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Mon Oct 01, 2018 12:31 am

Replaced all ADSRs with the same one from the toolbox and it now works !?
Who knows , might be an alpha issue ?
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Mon Oct 01, 2018 12:46 am

Lol, still some issues , Looks like if the release gets stuck at almost full levels.
I just move the knob slightly from zero and it plays full release, and not always .
Something is still wrong.

EDIT: The envelope gets stuck on "Full release" in FS and reaper ,when the decay is on full and the release is lifted slightly.

Taking a break ;)
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Re: Triggering switches with Midi notes.

Postby lalalandsynth » Mon Oct 01, 2018 5:42 pm

Sent you a PM Martin.
User avatar
lalalandsynth
 
Posts: 600
Joined: Sat Oct 01, 2016 12:48 pm

Previous

Return to General

Who is online

Users browsing this forum: No registered users and 55 guests